Our BIM content is available as individual families for Revit and templates for both Revit and Fabrication CADmep. The template files contain all pipes and fittings of each specific product line. These can be found on the right side of the screen when accessing the product line’s page.
Adapters
adapters-1
Male Adapter H x MPT
(4) This Adapter allows for a transition from a Female threaded pipe or fitting to a System XFR pipe or fitting.- When tested to the CAN/ULC S102.2 Standard, System XFR achieved a Flame Spread Rating of not greater than 25 and a Smoke Developed Classification of not greater than 50
- High impact strength in cold temperatures, exceeding CSA requirements
- Improved flow rates
- Lower thermal conductivity can reduce or eliminate the need for insulation
Female Adapter H x FPT
(4) This Adapter allows for a transition from a Male threaded pipe or fitting to a System XFR pipe or fitting.- When tested to the CAN/ULC S102.2 Standard, System XFR achieved a Flame Spread Rating of not greater than 25 and a Smoke Developed Classification of not greater than 50
- Meets National and Provincial Building Codes for high buildings, air plenums, noncombustible construction and penetrating a rate fire separation
- High impact strength in cold temperatures, exceeding CSA requirements
- Improved flow rates
- Lower thermal conductivity can reduce or eliminate the need for insulation
Pipe Trap Adapter H x Slip Joint
(2) This hub ended Adapter is installed under a bathroom sink, allowing for a transition from a tubular sink drain tail piece to a System XFR P-Trap.- When tested to the CAN/ULC S102.2 Standard, System XFR achieved a Flame Spread Rating of not greater than 25 and a Smoke Developed Classification of not greater than 50
- Meets National and Provincial Building Codes for high buildings, air plenums, noncombustible construction and penetrating a rate fire separation
- High impact strength in cold temperatures, exceeding CSA requirements
- Improved flow rates
- Lower thermal conductivity can reduce or eliminate the need for insulation
90º Pipe Trap Adapter H x Slip Joint
Create a water tight seal at a 90 degree angle through a Slip Joint connection at the end of this Adapter. Often used in a pedestal sink installation to allow for a trasition from a sink drain tail pipe.- When tested to the CAN/ULC S102.2 Standard, System XFR achieved a Flame Spread Rating of not greater than 25 and a Smoke Developed Classification of not greater than 50
- Meets National and Provincial Building Codes for high buildings, air plenums, noncombustible construction and penetrating a rate fire separation
- High impact strength in cold temperatures, exceeding CSA requirements
- Improved flow rates
- Lower thermal conductivity can reduce or eliminate the need for insulation
Tail Piece Adapter Sp x Slip Joint
(2) The adapter allows for an easy connection between spigot sink outlets and our System XFR piping system.- When tested to the CAN/ULC S102.2 Standard, System XFR achieved a Flame Spread Rating of not greater than 25 and a Smoke Developed Classification of not greater than 50
- Meets National and Provincial Building Codes for high buildings, air plenums, noncombustible construction and penetrating a rate fire separation
- High impact strength in cold temperatures, exceeding CSA requirements
- Improved flow rates
- Lower thermal conductivity can reduce or eliminate the need for insulation
Plastic MJ Spigot MJ Sp x H
(3) Easily transforms your M-J Cast Iron Pipe to a PVC System XFR piping system.- When tested to the CAN/ULC S102.2 Standard, System XFR achieved a Flame Spread Rating of not greater than 25 and a Smoke Developed Classification of not greater than 50
- Meets National and Provincial Building Codes for high buildings, air plenums, noncombustible construction and penetrating a rate fire separation
- High impact strength in cold temperatures, exceeding CSA requirements
- Improved flow rates
- Lower thermal conductivity can reduce or eliminate the need for insulation
Copper to DWV Adapter H x SJ
(2) Create a water tight seal when transitioning from Copper to System XFR pipe through a Slip Joint connection at the end of this Adapter.- When tested to the CAN/ULC S102.2 Standard, System XFR achieved a Flame Spread Rating of not greater than 25 and a Smoke Developed Classification of not greater than 50
- Meets National and Provincial Building Codes for high buildings, air plenums, noncombustible construction and penetrating a rate fire separation
- High impact strength in cold temperatures, exceeding CSA requirements
- Improved flow rates
- Lower thermal conductivity can reduce or eliminate the need for insulation
